Battery hedge trimmer
SPH 900 AE
Powerful, precise and only 4.9kg, the SPH 900 AE pole hedger takes the shaping of hedges and trees to new heights. Its advanced 400W brushless motor paired with two 48V 7.5Ah batteries, held in the battery harness, give over 200 minutes of non-stop power. The telescopic extension shaft reaches up to 4m. And with three speeds and six cutting positions to choose from, the SPH 900 AE gives you optimum control, whatever the job.
- Cordless pole hedger powered by an advanced 400W brushless motor
- Weighs just 4.9kg with a total tool length of 2.95cm
- 65cm telescopic shaft extends to 4m in height
- Foldable 65cm dual action laser-cut hedge blade adjusts 112° to six cutting positons
- Intuitive keypad adjusts the blade to three different speeds
- Suggested batteries: 2 x STIGA E-Power E 475 (7,5Ah) to be used with STIGA battery harness SBH 900 AE - sold separately
Battery hedge trimmer
SPH 900 AE
Often purchased together
Enjoy the strength of ePower.

Over 200 minutes of cutting time
Two 48V 7.5Ah boost batteries held in the battery harness SBH 900 connect to the handle, providing 200 minutes of hard-working power.

Advanced brushless motor – for superior performance
A strong, consistent torque, that’s also 25% more efficient. Unlike a traditional motor, the 400W brushless motor delivers the torque you need, without the maintenance hassles.

Secure handling: low vibrations
The soft-touch shaft cover ensures a safe, comfortable hold with minimum vibrations.

Six ergonomic angles – one lever activation
Easily rotate the cutting head into six positions – for a total of 112° coverage.
Description
Weighing only 4.9kg, the robust, ergonomic design of the SPH 900 AE pole hedger makes trimming comfortable and precise. Two powerful 48V 7.5Ah batteries, held in the battery harness SBH 900, give you an impressive 200 minutes of trimming on a single charge. And with the intuitive keypad on the soft-grip handle, you control the cutting speed – taking it up to 3300 spm at the push of a button. The 65cm telescopic shaft extends to 4m in length – putting tall hedges and branches within easy reach. Rotate the cutting head to position the 65cm dual action laser-cut blades. With six angles ranging from 25° above to 90° below horizontal, you’ll always achieve a precise, even cut. When your work is complete, simply unplug the connecting cable from the batteries, fold the blade back fully, and store your SHP 900 AE away.
Faqs
Which type of vegetation can you work on with this machine?
The engine this machine is fitted with, along with the high capacity of the batteries available and the latest-generation blade, allow you to tackle dense and difficult bushes, including for longer periods of use. The distance between the teeth means even thicker branches can be cut through.
What should I do when it is not being used?
During the times when it is not being used, we recommend you remove the battery from the machine, clean the teeth of the cutting element and place the machine in a safe place, ensuring you protect the blade when in the storage area.
Do the cutting blades need maintenance or sharpening?
Cutting hedges leads to detritus and dirt building up between the blades, an issue which without the necessary maintenance can lead to a loss of cutting performance.
After each period of use, you should therefore clean and oil the hedge cutting blades, ensuring you work with the machine in full safety in a horizontal position, laid steadily on the ground. The blades can be cleaned with a dry cloth, using a brush if needed to remove more stubborn dirt. The blades can be oiled by applying a thin layer of specific oil (Stiga recommends using non-polluting products) along the upper edge of the blade.
Please see the user manual for more information on this point.
After each period of use, you should therefore clean and oil the hedge cutting blades, ensuring you work with the machine in full safety in a horizontal position, laid steadily on the ground. The blades can be cleaned with a dry cloth, using a brush if needed to remove more stubborn dirt. The blades can be oiled by applying a thin layer of specific oil (Stiga recommends using non-polluting products) along the upper edge of the blade.
Please see the user manual for more information on this point.
The blades seem to be working as if they are not clean or fluid. What might have happened and what should I do?
Where the blades tend to catch and you notice a reduction of cutting performance, possibly along with more blade noise, you must check the cutting element.
If the problem persists even after cleaning and oiling the blades, the solution is to sharpen them.
For reasons of safety, this is best performed by an authorised Stiga vendor. Once sharpened, the cutting system will return to working precisely and fluidly.
Lastly, please note that an excessively worn or damaged blade must not be sharpened but always replaced. Again in this case, the Stiga vendor network is always available.
If the problem persists even after cleaning and oiling the blades, the solution is to sharpen them.
For reasons of safety, this is best performed by an authorised Stiga vendor. Once sharpened, the cutting system will return to working precisely and fluidly.
Lastly, please note that an excessively worn or damaged blade must not be sharpened but always replaced. Again in this case, the Stiga vendor network is always available.
Specifications
General info
EAN/UPC
8008984844209
SKU
279710038/ST1
Level
Expert
Power
Power source
Battery
Number of batteries needed - not included
1
Suggested battery capacity
2 x 7,5 Ah
ePower
Yes
Power
0.4 kW
Voltage
48 Volt
Battery kit
Not included
Motor type
Brushless
Maximum motor speed
16500 rpm
Lithium battery nominal energy
324 Wh
Working time (+/- 20%)
200 min
Cutting system
Cutting length
51 cm
Blade length
65 cm
Blade type
Dual action - Laser cut
Blade teeth speed
3300 spm
Teeth distance
34 mm
Cutting capacity (diameter)
27 mm
Equipment
Handle type
Fix
Vibe Control System (VCS)
Yes
Soft grip handle
Yes
Shaft extension
60 cm
Tools kit
Battery charger
Single fast
Battery charger output current
1.5 A
Vibration and noise data
Guaranteed sound power level (LwA) - dB(A)
93
Measured sound power level dB(A)
89.8
Measured sound pressure level at operator ear dB(A)
77.4
Vibration level front handle (m/s2)
5.58
Vibration level rear handle (m/s2)
3.54
Overall dimensions
Pack weight
8.2 kg
Product weight without battery
5.18 kg
Product weight
5.18 kg
Product length
2600 mm
Product width
210 mm
Product height
150 mm
What's in the box

Harness
Downloads
User manual Download